NEET Measuring Devices ( Galvanometer, Voltmeter and Ammeter & Meter Bridge ) MCQs & PYQs

Current through each resistor is 220/1100 = 1/5 A

Total current through ammeter = 3 * 1/5 A= 3/5 A

Initial Setup:

1. An ammeter and a voltmeter are connected in series to a cell.
2. The ammeter reading is
   $A$ 

   (current through the circuit).

3. The voltmeter reading is
   $V$ 

   (potential difference across the cell).

What Happens When a Resistance is Added in Parallel with the Voltmeter?

• The voltmeter has a high internal resistance (
  $R_v$ 

  ) to minimize current flow through it.

• When an additional resistance (
  $R$ 

  ) is connected in parallel with the voltmeter, the effective resistance of the voltmeter decreases because: $$R_{\text{eff}} = \frac{R_v \cdot R}{R_v + R}.$$ 

  Since $R$ 

  is finite, $R_{\text{eff}} < R_v$ 

  .

Effect on the Circuit:

1. Decrease in total resistance:
   • The voltmeter (and its parallel combination) is in series with the ammeter.
   • The decrease in
     $R_{\text{eff}}$ 

     reduces the total resistance of the circuit.

   • Lower resistance means higher total current through the circuit (Ohm's law:
     $I = \frac{V}{R_{\text{total}}}$ 

     ).

   • Thus, the ammeter reading (
     $A$ 

     ) increases.

2. Voltage across the voltmeter decreases:
   • With the reduced effective resistance of the voltmeter, a smaller fraction of the total voltage is dropped across it.
   • Hence, the voltmeter reading (
     $V$ 

     ) decreases.

Conclusion:

When a resistance is added in parallel with the voltmeter:

• The ammeter reading (
  $A$ 

  ) increases.

• The voltmeter reading (
  $V$ 

  ) decreases.

Case 1: Using the galvanometer as a voltmeter

Given Data:

• Coil resistance of galvanometer:
  $R_g = 100 \, \Omega$ 

  ,

• Full-scale deflection current of the galvanometer:
  $I_g = 50 \, \mu A = 50 \times 10^{-6} \, \text{A}$ 

  ,

• Range of the voltmeter to be designed:
  $V = 50 \, \text{V}$ 

  .

Total Resistance Required ( $R_v$

):

The total resistance

$R_v$

of the voltmeter is determined using Ohm's law:

$$R_v = \frac{V}{I_g} = \frac{50}{50 \times 10^{-6}} = 10^6 \, \Omega.$$

Since the galvanometer already has a resistance

$R_g = 100 \, \Omega$

, the additional series resistance

$R_s$

required is:

$$R_s = R_v - R_g = 10^6 - 100 \approx 10^6 \, \Omega.$$

Conclusion:

• To use the galvanometer as a voltmeter of range 50 V, the series resistance required is
  $\mathbf{10^6 \, \Omega}$ 

  (Option A is correct).

Case 2: Using the galvanometer as an ammeter

Given Data:

• Full-scale deflection current of the galvanometer:
  $I_g = 50 \, \mu A = 50 \times 10^{-6} \, \text{A}$ 

  ,

• Resistance of the galvanometer:
  $R_g = 100 \, \Omega$ 

  ,

• Range of the ammeter to be designed:
  $I = 10 \, \text{mA} = 10 \times 10^{-3} \, \text{A}$ 

  .

Shunt Resistance ( $R_s$

):

The shunt resistance is connected in parallel with the galvanometer to allow the additional current (

$I - I_g$

) to pass through it. The voltage across the galvanometer and the shunt must be equal:

$$V_g = V_s \quad \Rightarrow \quad I_g R_g = I_s R_s,$$

where

$I_s = I - I_g = 10 \times 10^{-3} - 50 \times 10^{-6} = 9.95 \times 10^{-3} \, \text{A}$

.

Using the above relation, the shunt resistance is:

$$R_s = \frac{I_g R_g}{I_s} = \frac{(50 \times 10^{-6}) \cdot 100}{9.95 \times 10^{-3}} = 0.5 \, \Omega.$$

Conclusion:

• To use the galvanometer as an ammeter of range 10 mA, the shunt resistance required is
  $\mathbf{0.5 \, \Omega}$ 

  (Option C is correct).

Final Answer:

The correct options are:

$$\boxed{\text{A and C}}$$

To solve this, we need to determine the shunt resistance (

$R_S$

) required to extend the range of the milliammeter from 10 mA to 1 A.

Key Points:

1. Milliammeter Current and Resistance:
   • Maximum current through the milliammeter coil:
     $I_m = 10 \, \text{mA} = 0.01 \, \text{A}$ 

     ,

   • Resistance of the milliammeter coil:
     $R_m = 1 \, \Omega$ 

     .

2. Total Current for the Ammeter:
   • The total current to be measured by the modified ammeter:
     $I = 1 \, \text{A}$ 

     .

3. Shunt Current:
   • The shunt carries the remaining current,
     $I_S = I - I_m = 1 \, \text{A} - 0.01 \, \text{A} = 0.99 \, \text{A}$ 

     .

4. Voltage Across Shunt and Milliammeter:
   • The shunt is connected in parallel with the milliammeter, so the voltage across them is the same:
     $$V_m = V_S.$$ 
5. Ohm's Law:
   • Voltage across the milliammeter:
     $$V_m = I_m \cdot R_m = 0.01 \cdot 1 = 0.01 \, \text{V}.$$ 
   • Voltage across the shunt:
     $$V_S = I_S \cdot R_S = 0.01 \, \text{V}.$$ 
6. Solve for Shunt Resistance (
   $R_S$ 

   ):

   • From the voltage equation:
     $$R_S = \frac{V_S}{I_S} = \frac{0.01}{0.99} = \frac{1}{99} \, \Omega.$$ 

Final Answer:

The required shunt resistance is:

$$\boxed{\frac{1}{99} \, \Omega}.$$

To construct an ammeter that can read currents up to

$2.0 \, \text{A}$

, we need to calculate the resistance of the shunt. Here's the step-by-step calculation:

1. Full-scale current through the coil:
   The coil takes $1 \, \text{mA} = 10^{-3} \, \text{A}$ 

   for full-scale deflection.

2. Remaining current through the shunt:
   When the total current is $2.0 \, \text{A}$ 

   , the current through the shunt is:

   $$I_s = I_{\text{total}} - I_c = 2.0 - 10^{-3} = 1.999 \, \text{A}.$$ 

3. Voltage across the coil:
   The resistance of the coil is $25 \, \Omega$ 

   . Using Ohm's law, the voltage across the coil is:

   $$V_c = I_c R_c = (10^{-3})(25) = 0.025 \, \text{V}.$$ 

4. Resistance of the shunt:
   The voltage across the shunt must equal the voltage across the coil:  $$V_s = V_c = 0.025 \, \text{V}.$$Using Ohm's law for the shunt:

    

   $$R_s = \frac{V_s}{I_s} = \frac{0.025}{1.999} \approx 1.25 \times 10^{-2} \, \Omega.$$ 

Thus, the resistance of the shunt is:

$$\boxed{1.25 \times 10^{-2} \, \Omega.}$$

To convert a galvanometer into a voltmeter, a high resistance \(R\) is connected in series: \(V = I_g(G + R) \implies 10 = 10^{-3}(12 + R) \implies R = 9988\ \Omega\).

Deflection is inversely proportional to total circuit resistance. Using $frac{\theta_1}{\theta_2} = \frac{R_2 + G}{R_1 + G}$, we get $\frac{30}{20} = \frac{R_2 + 50}{2950 + 50}$, giving $\R_2 = 4450 \Omega$.

The shunt resistance is $S = \frac{G}{499}$. The equivalent resistance of the ammeter is $R_A = \frac{GS}{G+S} = \frac{G(G/499)}{G + G/499} = \frac{1}{500} G$.